Search found 1093 matches

by Alan_M
Sat Mar 30, 2024 17:46
Forum: For Sale
Topic: Elite convertible !!!!
Replies: 3
Views: 400

Elite convertible !!!!

I’m sure this car has featured on here, but can’t find post at the moment.

What’s left of an Elite for sale on Facebook. Not sure there’s much usable on it, but does seem to have all windscreen trim.

https://www.facebook.com/marketplace/it ... 672319254/
by Alan_M
Fri Mar 29, 2024 09:51
Forum: Engine and Gearbox
Topic: Carb fuel line removal
Replies: 3
Views: 234

Re: Carb fuel line removal

Nothing special, just the nut on the end of the fuel line to each carb. If fully refurbing carbs you will need to take the carb off the car, including the top cover. Otherwise it’s going to be a struggle to remove the float, float valve and top gasket. One thing to note - when removing the pin that ...
by Alan_M
Tue Mar 26, 2024 23:11
Forum: Events, Meetings and a "Run Out"
Topic: NEC Restoration Show - 22-24 March 2024
Replies: 46
Views: 4840

Re: NEC Restoration Show - 22-24 March 2024

In a word - no. Anodised trims were wrapped, a few minor paint blemishes, but biggest issue looked to be drivers door, which had dropped significantly. Window frames didn't look great either. Alan and I reckoned it would have been a good buy at £12K. Particularly as it's done very few miles in last...
by Alan_M
Tue Mar 26, 2024 13:33
Forum: Events, Meetings and a "Run Out"
Topic: NEC Restoration Show - 22-24 March 2024
Replies: 46
Views: 4840

Re: NEC Restoration Show - 22-24 March 2024

MetBlue wrote:
Tue Mar 26, 2024 12:41
Looks like the Excel being auctioned didn't sell. It shows as a buy it now price of £8,650.
The gold Elite looks to have sold for £15,750.

Tony
The Excel reached £6k in the auction, but as you say wasn’t sold.
by Alan_M
Thu Mar 21, 2024 00:27
Forum: Bodywork, Fitments, Interior and Trim
Topic: Elite/Eclat carpet templates
Replies: 5
Views: 1315

Re: Elite/Eclat carpet templates

pistolpete wrote:
Wed Mar 20, 2024 18:42
I am keen to put carpets in my car and was wondering where you where on the templates, as I am keen to borrow them
Coverdale have templates - they sent a set to me to check fit when I ordered a set from them. I marked up what I needed and returned them.
by Alan_M
Thu Mar 21, 2024 00:24
Forum: General
Topic: Electric window
Replies: 14
Views: 556

Re: Electric window

If applying power make sure you put negative to the body of the motor and positive to one of the contacts in the plug - one will be up, the other down.
by Alan_M
Wed Mar 13, 2024 10:34
Forum: Events, Meetings and a "Run Out"
Topic: NEC Restoration Show 2024 - Call for Volunteers
Replies: 31
Views: 1441

Re: NEC Restoration Show 2024 - Call for Volunteers

Hawaiis0 wrote:
Mon Mar 11, 2024 23:35
What's the dress code?

Image
Are these likely to be available to get hold of before the show?
by Alan_M
Tue Mar 12, 2024 12:20
Forum: Events, Meetings and a "Run Out"
Topic: Lotus in the Peak 2024
Replies: 53
Views: 4061

Re: Lotus in the Peak 2024

So being a LITP newbie, do I get from this there will be nothing organized for during the day on Saturday? Maria was hoping to visit something in Matlock at some point on our travels and from this it looks like she could do that on the Saturday? In which case we will do that and plan the few days e...
by Alan_M
Sun Mar 10, 2024 11:33
Forum: General
Topic: Door lights
Replies: 10
Views: 426

Re: Door lights

The switch position can be adjusted. Try holding in each one as far as it will go to see if that turns out the lights. If it does adjust switch. If not, then going to need to use tester on switches, or pull wires as Tony says to eliminate each one in turn. Driver’s side not too difficult, passenger’...
by Alan_M
Tue Mar 05, 2024 10:30
Forum: Bodywork, Fitments, Interior and Trim
Topic: Steering stiff
Replies: 10
Views: 1390

Re: Steering stiff

There are 2 different columns fitted depending on year.
I had about 15mm in/out play on an early one - lower bearing completely shot. Also the lower dome that bolts to the bulk head was rotten - managed to get a good used one.
by Alan_M
Thu Feb 29, 2024 22:23
Forum: General
Topic: Steering Rack - Why rigid mounted not isolation bush
Replies: 5
Views: 393

Re: Steering Rack - Why rigid mounted not isolation bush

As Marten says - more precise control. What our cars are renowned for, so I’d certainly want to keep the original setup. Having a rubber bush will allow small movements of the rack losing some of the precision and feedback between road and hands. Similar concept to using rose joints rather than rubb...
by Alan_M
Thu Feb 29, 2024 20:17
Forum: For Sale
Topic: Shaun W’s old Excel for sale.
Replies: 9
Views: 730

Re: Shaun W’s old Excel for sale.

Hawaiis0 wrote:
Thu Feb 29, 2024 18:04
Link doent open for me
The post has gone.
There were a lot of people very quickly interested - so may have sold
Or
As it was on a group that doesn’t allow selling, might have been removed.
by Alan_M
Wed Feb 28, 2024 20:42
Forum: Servicing, Belts, Fuels and Oils
Topic: Valvoline VR1 20W50 - £29.99
Replies: 3
Views: 525

Re: Valvoline VR1 20W50 - £29.99

You can also get 20l from Tayna for £117.48 delivered.

I “think” that’s their normal price.
by Alan_M
Wed Feb 28, 2024 11:27
Forum: For Sale
Topic: Shaun W’s old Excel for sale.
Replies: 9
Views: 730

Re: Shaun W’s old Excel for sale.

Pete Boole wrote:
Wed Feb 28, 2024 09:09
One of the best Excels available. How much is it?

Pete
Doesn’t say.