Hi again. I hope, everyone is doing fine and driving well
I recently changed the Clutch of my Excel... and I can´t shake the feeling, that the are easier ways to do that than mine...
Soooo... first, I unbolted the Diff except the Axles - and pushed it back. Then I hooked up the Engine to a Lift, unbolted the Engine-Mounts, lifted the Engine a bit and fiddled the Mounts out of the Car, took off the upper Radiator Hose, the middle Part of the Exhaust, the Tranny-Mount and unbolted the Prop-Shaft. Next, I disconnected the Speedo and Clutch-Cylinder from the Tranny and then I pushed the whole Drivetrain forward - with everything else still connected to the Engine and the last bit of the rear of the Tranny then resting on the Tunnel.
I´m not sure if that works with the original Radiator-Fans in place, because they are quite tall.
After that there was enough Space to push the Prop-Shaft out of the Tranny. Then I unbolted the Tranny from the Engine, pushed the Engine further forward and got the Tranny out.
The only other Way that came to my mind was the classical Method of getting the whole Drivetrain out through the Engine-Bay - but that definitely is a lot more Work.
Nevertheless, the Excel is back on the Road again for a couple of Days, now, and is a lot of Fun, again, in spite of the abysmal Weather, here...
Changing Clutch - the most awkward way?
Moderator: Board Moderators
-
- Junior Poster
- Posts: 69
- Joined: Wed Sep 01, 2021 18:14
-
- Regular Poster
- Posts: 130
- Joined: Tue Aug 10, 2021 20:38
- Model: excel
- Colour: red
- Year: 1985
- Location: NL
- Contact:
Re: Changing Clutch - the most awkward way?
Once you've done it a few times (because Lotus ) pulling the engine/transmission is probably a lot more comfortable. Provided you have stuff like an angle adjustable hoist etcOldtimer_Basis wrote: ↑Tue Nov 14, 2023 16:29The only other Way that came to my mind was the classical Method of getting the whole Drivetrain out through the Engine-Bay - but that definitely is a lot more Work.
-
- Junior Poster
- Posts: 69
- Joined: Wed Sep 01, 2021 18:14
Re: Changing Clutch - the most awkward way?
I just pulled the Engine once... well, there are Cars where this is more of a hassle, but I can imagine things that are more fun... like driving
Just out of curiosity: Everywhere you look, there are only a few Centimeters missing for just simply unbolting the Tranny and getting it out of the Excel... removing the Tranny from the "Original" - I mean the Eclat and Elite is easy, right?
Just out of curiosity: Everywhere you look, there are only a few Centimeters missing for just simply unbolting the Tranny and getting it out of the Excel... removing the Tranny from the "Original" - I mean the Eclat and Elite is easy, right?
-
- Senior Poster
- Posts: 3733
- Joined: Tue Apr 04, 2006 21:28
- Model: Elite
- Colour: Monaco White
- Year: 1974
- Location: Nottingham
Re: Changing Clutch - the most awkward way?
The chassis on the Elite is different to the Excel - the "Y" section at the front is shorter, so probably no easier to remove the gearbox than it is with the Excel.
Pete
Pete
- bash
- Senior Poster
- Posts: 2229
- Joined: Thu Nov 03, 2005 15:34
- Model: Se, V8
- Colour: white
- Year: 1986
- Location: Doncaster
- Contact:
Re: Changing Clutch - the most awkward way?
Blimey, that sounds arkward. The engine can be separated from the gearbox and pulled out on a crane that you had out anyway, or, engine and gearbox together without touching the diff or prop.
Two things are infinite: the universe and human stupidity; and I'm not sure about the universe.
-
- Senior Poster
- Posts: 243
- Joined: Mon Aug 23, 2021 21:38
- Model: Excel SE
- Colour: Blue
- Year: 1990
- Location: Uffington
Re: Changing Clutch - the most awkward way?
I've taken mine out and put it in a few times over the last few years and found its not too much of a problem.
No need to touch the differential or prop shaft, the end of the prop is on a splined joint and just pulls out of the gearbox as the engine/gearbox moves forward.
Remove the front pipes from the exhaust rather than the middle box
I lifted the engine out with the crane at the side of the car not the front.
A load leveler is required!
No need to touch the differential or prop shaft, the end of the prop is on a splined joint and just pulls out of the gearbox as the engine/gearbox moves forward.
Remove the front pipes from the exhaust rather than the middle box
I lifted the engine out with the crane at the side of the car not the front.
A load leveler is required!
Of all the things I have lost I think I miss my mind the most...
1952 MG TD
1957 MGA 1500
1959 Austin Healey Sprite
1975 MG Midget 1500
1990 Lotus Excel
1952 MG TD
1957 MGA 1500
1959 Austin Healey Sprite
1975 MG Midget 1500
1990 Lotus Excel